Corner Wall
Repair Kits
Carbon Fiber Corner Wall Repair System
The professional-grade solution for cracked and inward-moving foundation wall corners. Engineered for contractors and engineers who need a fast, non-intrusive repair. Works on poured and block (CMU) walls. stronger than steel, non-corrosive, and maintenance-free.
Who Can't Afford Failure
The Rhino Corner Wall Repair Kit gives contractors and structural engineers a faster, stronger, and more cost-effective solution for cracked and inward-moving foundation wall corners without excavation or obtrusive hardware.
Every Corner Repair
Residential and commercial foundation wall corners of all types. If it's cracking or moving inward, the Rhino Corner Wall Repair Kit has it covered.
- Cracked poured foundation corners
- Inward-moving corner walls
- Beam pocket stress damage
- Proactive corner reinforcement
- Concrete block corner repair
- CMU basement wall corners
- Block and masonry corner reinforcement and stabilization
- Finished & unfinished basement corners
- Crawlspace corner walls
- Below-grade corner stabilization
- High moisture foundation corners
- Corners in good condition — preventive strengthening
- Beam pocket locations at risk
- Pre-sale structural reinforcement
- Increased load-bearing capacity
- Beams pocketed over wall corners
- Concentrated load cracking
- Settlement-related corner movement
- Poor original construction details
| Material | High-Modulus Carbon Fiber CFRP |
| Tensile Strength | 102.4 ksi (Bidirectional) |
| Available Weights | 560 GSM Bidirectional |
| Strap Width | 5.5" (Bidirectional) |
| Strap Length | 10' per strap |
| Straps per Kit | 4 |
| Epoxy System | RCF Saturant-Adhesive Epoxy · Mix Ratio 1:1 |
| Cure Time | 2–10 hrs initial · 24 hrs recommended for full strength |
| Wall Types | Poured Concrete · Block (CMU) |
| Finish | Smooth, Flat, Paintable — No Added Footprint |
| Corrosion | Non-Corrosive |
| Maintenance | None |
*Tensile strength of individual carbon fibers vs mild structural steel. Actual CFRP system performance is governed by composite action of carbon fiber and epoxy resin. Unidirectional carbon fiber is not appropriate for repairs requiring high anisotropic strength — Bidirectional CFRP is better suited for those applications.
We built the Rhino Corner Wall Repair Kit to outperform steel angle brackets, excavation-based methods, and epoxy-only repairs on strength, longevity, and ease of install.
The Rhino Corner Wall Repair Kit is designed for field crews. Fast, repeatable, and completable in a single day. No excavation, no obtrusive hardware.
Select Your Kit
Choose 560 GSM Bidirectional for all-direction corner strength for vertical load reinforcement. The kit includes 4 straps at 10' each with RCF Saturant-Adhesive Epoxy.
Prep the Corner
Lay plastic or drop cloth around the work area. Grind or clean the corner surface to remove paint, coatings, and any loose material — achieving a bare, clean concrete or masonry surface for full epoxy adhesion.
Repair Any Cracks
Fill any existing cracks using hydraulic cement or RCF High Strength Anchoring Epoxy Paste before applying carbon fiber. The surface must be completely clean and crack-free prior to strap application.
Measure & Mark
Measure and mark the strap locations on the corner. Straps should be centered on the corner and span both wall faces to fully engage the corner joint and transfer load through the carbon fiber.
Apply Epoxy to Surface
Apply an even coat of RCF Saturant-Adhesive Epoxy (1:1 mix ratio) to the concrete or masonry surface over the full area where the carbon fiber strap will be placed, using the supplied epoxy gun.
Apply Carbon Fiber Strap
Lay the carbon fiber strap over the epoxy-coated corner surface — straight, tight, and fully in contact with the wall on both sides of the corner. Work the strap into the epoxy with a roller or gloved hands.
Saturate & Coat
Apply a second coat of epoxy over the top of the carbon fiber strap, fully saturating the fabric. Spread evenly with a putty knife to ensure complete coverage and a smooth, flat finish on both wall faces.
Cure & Finish
Allow 2–10 hours for initial cure depending on temperature. Wait 24 hours for full strength development before loading. The finished surface is paintable, coverable, and requires zero maintenance.
Everything you need to know about Rhino Carbon Fiber Corner Wall Repair Kit. Can't find an answer? Contact our technical team directly.
Stop Bracing.
Start Reinforcing.
Find your nearest distributor, download the full Technical Sheet, or connect with a Rhino Carbon Fiber sales member to discuss your next bowed wall project.
Corner Wall
Repair Kits
Carbon Fiber Corner Wall Repair System
The professional-grade solution for cracked and inward-moving foundation wall corners. Engineered for contractors and engineers who need a fast, non-intrusive repair. Works on poured and block (CMU) walls. Stronger than steel, non-corrosive, and maintenance-free.
Who Can't Afford Failure
The Rhino Corner Wall Repair Kit gives contractors and structural engineers a faster, stronger, and more cost-effective solution for cracked and inward-moving foundation wall corners without excavation or obtrusive hardware.
Every Corner Repair
Residential and commercial foundation wall corners of all types. If it's cracking or moving inward, the Rhino Corner Wall Repair Kit has it covered.
- Cracked poured foundation corners
- Inward-moving corner walls
- Beam pocket stress damage
- Proactive corner reinforcement
- Concrete block corner repair
- CMU basement wall corners
- Block and masonry corner reinforcement and stabilization
- Finished & unfinished basement corners
- Crawlspace corner walls
- Below-grade corner stabilization
- High moisture foundation corners
- Corners in good condition — preventive strengthening
- Beam pocket locations at risk
- Pre-sale structural reinforcement
- Increased load-bearing capacity
- Beams pocketed over wall corners
- Concentrated load cracking
- Settlement-related corner movement
- Poor original construction details
| Material | High-Modulus Carbon Fiber CFRP |
| Tensile Strength | 102.4 ksi (Bidirectional) |
| Available Weights | 560 GSM Bidirectional |
| Strap Width | 5.5" (Bidirectional) |
| Strap Length | 10' per strap |
| Straps per Kit | 4 |
| Epoxy System | RCF Saturant-Adhesive Epoxy · Mix Ratio 1:1 |
| Cure Time | 2–10 hrs initial · 24 hrs recommended for full strength |
| Wall Types | Poured Concrete · Block (CMU) |
| Finish | Smooth, Flat, Paintable — No Added Footprint |
| Corrosion | Non-Corrosive |
| Maintenance | None |
*Tensile strength of individual carbon fibers vs mild structural steel. Actual CFRP system performance is governed by composite action of carbon fiber and epoxy resin. Unidirectional carbon fiber is not appropriate for repairs requiring high anisotropic strength — Bidirectional CFRP is better suited for those applications.
We built the Rhino Corner Wall Repair Kit to outperform steel angle brackets, excavation-based methods, and epoxy-only repairs on strength, longevity, and ease of install.
The Rhino Corner Wall Repair Kit is designed for field crews. Fast, repeatable, and completable in a single day. No excavation, no obtrusive hardware.
Select Your Kit
Choose 560 GSM Bidirectional for all-direction corner strength for vertical load reinforcement. The kit includes 4 straps at 10' each with RCF Saturant-Adhesive Epoxy.
Prep the Corner
Lay plastic or drop cloth around the work area. Grind or clean the corner surface to remove paint, coatings, and any loose material — achieving a bare, clean concrete or masonry surface for full epoxy adhesion.
Repair Any Cracks
Fill any existing cracks using hydraulic cement or RCF High Strength Anchoring Epoxy Paste before applying carbon fiber. The surface must be completely clean and crack-free prior to strap application.
Measure & Mark
Measure and mark the strap locations on the corner. Straps should be centered on the corner and span both wall faces to fully engage the corner joint and transfer load through the carbon fiber.
Apply Epoxy to Surface
Apply an even coat of RCF Saturant-Adhesive Epoxy (1:1 mix ratio) to the concrete or masonry surface over the full area where the carbon fiber strap will be placed, using the supplied epoxy gun.
Apply Carbon Fiber Strap
Lay the carbon fiber strap over the epoxy-coated corner surface — straight, tight, and fully in contact with the wall on both sides of the corner. Work the strap into the epoxy with a roller or gloved hands.
Saturate & Coat
Apply a second coat of epoxy over the top of the carbon fiber strap, fully saturating the fabric. Spread evenly with a putty knife to ensure complete coverage and a smooth, flat finish on both wall faces.
Cure & Finish
Allow 2–10 hours for initial cure depending on temperature. Wait 24 hours for full strength development before loading. The finished surface is paintable, coverable, and requires zero maintenance.
Everything you need to know about Rhino Carbon Fiber Corner Wall Repair Kit. Can't find an answer? Contact our technical team directly.
Stop Patching.
Start Reinforcing.
Find your nearest distributor, download the full Technical Sheet, or connect with a Rhino Carbon Fiber sales member to discuss your next corner wall repair project.